野王,日本xxxx片免费观看,丁香五月婷婷亚洲,六月丁香婷婷大团结

安全管理網

安全閥維修工作總結

  
評論: 更新日期:2016年07月09日

    本人是寶清縣鍋爐壓力容器檢驗所一名特種設備檢驗                                                               
    員,于2010年開始從事安全閥校驗工作,工作3年中共校驗安全閥300余只。下面我談?wù)勅绾巫龊冒踩y的維護和檢查工作。                                                               
    要使安全閥動作靈敏、可靠和密封性能良好,必須在鍋                                                               
    爐、壓力容器、壓力管道的運行過程中加強維護和檢查。                                                               
    (一)要經常保持安全閥的清潔,防止閥體彈簧等被油                                                               
    垢臟物填滿或被腐蝕,防止安全閥排放管被油污或其他異物堵塞。經常檢查鉛封是否完好,防止杠桿式安全閥的重錘松動或被移動,防止隨意擰動。                                                               
    (二)發現安全閥有泄漏跡象時,應時及更換或檢修。                                                               
    禁止用加大載荷(如過分?jǐn)Q緊彈簧式安全閥的調節螺絲或在杠桿式安全閥的杠桿上加掛重物等)的方法來消除泄漏。為防止閥瓣和閥座被氣體中的油垢等臟物粘住,致使安全潤不能正常開啟,對用于空氣、蒸汽或帶有粘滯性臟物但排放不                                                               
    會造成危害的其他氣體的安全閥,應定期做手提排放試驗。                                                               
    (三)為保持安全閥靈敏可靠,每年至少做一次定期校                                                               
    驗。定期校驗的內容一般包括動態檢查和解體檢查。動態檢查的主要內容是檢查安全閥的開啟壓力、回座壓力、密封程度以及在額定排放壓力下的開啟高度等,其要求與安全閥調試時相同。若動態檢查不合格,或在運行中發現有泄漏等異                                                                                                                                   
    常情況時,則應作解體檢查。解體后仔細檢查安全閥的所有零部件有無裂紋、傷痕、磨損、腐蝕、變形等情況,并根據缺陷的大小和損壞程度予以修復或更換,最后組裝,進行動態檢查。                                                               
    特種設備使用單位要高度重視安全閥的故障消除、維修和檢查(維護)工作以及相關事故的教訓警示和安全閥在承壓類特種設備上的重要性。                                                               
    特種設備使用單位應貫徹執行《特種設備安全監察條例》,嚴格遵守安全操作規程和規章制度,除對在用的承壓類特種設備本體進行經常性的日常維護保養和檢查外,也要對其安全附件按規定進行定期校驗和維護,并納入特種設備安全管理工作,對發現的隱患,及時整改,消除隱患,并真正落實企業主體責任,確保特種設備的安全運行。                                                                                                                               
    寶清縣鍋爐壓力容器檢驗所                                                               
    張文卉篇二:安全閥校驗工作總結                                                                           
    安全閥校驗工作總結                                                                                                                               
    本人是漯河市特種設備安全檢測中心一名特種設備檢驗人員。于2010年開始從事安全閥校驗工作,工作3年中共校驗安全閥500余只。下面我談?wù)勅绾巫龊冒踩y的維護和檢查工作。  要使安全閥動作靈敏、                                                                                                                                                                                               
    可靠和密封性能良好                                                               
    器、壓力管道的運行過程中加強維護和檢查。                                                                                                                                                                                                                                                               
    一、                                                               
    滿或被腐蝕,防止安全閥排放管被油污或其他異物堵塞。經常檢查鉛                                                                                                                                                                                               
    封是否完好,                                                               
    動。                                                                                                                                                                                                                                                               
    二、發現安全閥有泄漏跡象時,應時及更換或檢修。禁止用加大載荷(如過分?jǐn)Q緊彈簧式安全閥的調節螺絲或在杠桿式安全閥的杠桿上加掛重物等)的方法來消除泄漏。為防止閥瓣和閥座被氣體中的油垢等臟物粘住,致使安全潤不能正常開啟,對用于空氣、蒸汽或帶有粘滯性臟物但排放不會造成危害的其他氣體的安全閥,應定期做手提排放試驗。                                                                                                                                                                                               
    三、為保持安全閥靈敏可靠,每年至少做一次定期校驗。定期校驗的內容一般包括動態檢查和解體檢查。動態檢查的主要內容是檢查安全閥的開啟壓力、回座壓力、                                                                                                                                                                                               
    密封程度以及在額定排放壓力下的運行中發現有泄漏等異常情況時則應作解體檢查。解體后仔細檢查安                                                                                                                                                                                                                                                                   
    據缺陷的大小和損壞程度予以修復或更換,最后組裝,進行動態檢查。                                                               
    特種設備使用單位要高度重視安全閥的故障消除、維修和檢查維護,工作以及相關事故的教訓警示和安全閥在承壓類特種設備上的重要性。                                                                                                                                                                                                                                                               
    特種設備使用單位應貫徹執行《特種設備安全監察條例》嚴格遵守安全操作規程和規章制度,除對在用的承壓類特種設備本體進行經常性的日常維護保養和檢查外,也要對其安全附件按規定進行定期校驗和維護,并納入特種設備安全管理工作,                                                               
    時整改,消除隱患,                                                               
    運行。                                                                                                                               
    總結人:董彥勛                                                               
    2013年2月26日篇三:安全閥校驗及維修培訓總結                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    篇四:安全閥種類總結                                                                           
    安全閥的種類很多,但通常按以下方法進行分類。                                                               
    按結構形式分類 根據結構特點或閥瓣最大開啟高度與閥座直徑之比(h/d),安全閥一般可以分為以下幾種:                                                               
    1) 杠桿重錘式安全閥。重錘的作用力通過杠桿放大后加載于閥瓣。在閥門開啟和關閉過程                                                               
    中載荷的大小不變,因此由閥桿傳來的力基本上是不變的。其缺點是對振動較敏感,且回座性能較差。這種結構的安全閥只能用在固定設備上,重錘的重量一般不應超過60kg,以免操作困難。                                                               
    2) 彈簧式安全閥。 利用壓縮彈簧的力來平衡閥瓣的壓力,并使其密封的安全閥。 該類安                                                               
    全閥的優點在于比重錘式安全閥輕便,靈敏度高,安裝位置沒嚴格限制。缺點是作用在閥桿上的力隨彈簧的變形而產生變化;同時,當溫度較高時,應注意彈簧的隔熱和散熱。這類安全閥的彈簧作用力一般不應超過20000n;過大、過硬的彈簧不適于精確的工作。                                                               
    3) 脈沖式安全閥,又稱先導式安全閥。 它把主閥和輔閥設計在一起,通過輔閥的脈沖作                                                               
    用帶動主閥動作。這種結構通常用于大口徑、大排量及高壓系統。                                                               
    大直徑疏水管路上用的脈沖式安全閥,也是有主閥和輔閥組成。輔閥為口徑很小的直接載荷式安全閥,它與主閥相連。當系統超壓時,輔閥首先開啟,排放介質,從而驅動或控制主閥閥瓣開啟,大量排放介質。                                                               
    4) 微啟式安全閥。 閥瓣的開啟高度為閥座通徑的1/20~1/40,即安全閥的閥瓣開啟高度很                                                               
    小,適用于液體介質和排量不大的場合。由于液體介質是不可壓縮的。少量排除即可使壓力下降。                                                               
    5) 全啟式安全閥。閥瓣的開啟高度為閥座通徑的1/4~1/3。在安全閥的閥瓣處設有反沖盤,                                                               
    借助于氣體介質的膨脹沖力,使閥瓣開啟到足夠的高度,從而達到排量要求。這種結構的安全閥使用較多,靈敏度亦較高,但兩個調節環的位置很難調整,必須十分認真調整才能達到要求,這對初次使用者帶來很多困難。因此,又開發了一種被簡化了的結構。這種結構的調整較為方便,但靈敏度稍受影響。若用于一般蒸汽鍋爐和蒸汽管道上影響不大。                                                               
    6) 全封閉式安全閥。安全閥開排放時,介質不會向外界泄漏,而是通過排泄管排放掉。這                                                               
    種結構適用于易燃、易爆,有毒有害介質。                                                               
    7) 半封閉式安全閥。 安全閥開啟排放時,介質一部分通過排泄管排放,而另一部分從閥                                                               
    蓋與閥桿的配合處向外泄漏。這種結構的安全閥適用于一般蒸汽和對環境無污染的介質。                                                               
    8) 敞開式安全閥。安全閥開啟排放時,介質不引導管道或容器內,而直接由閥瓣上方排放                                                                                                                                   
    到大氣中。這種安全閥適用于對環境無污染的介質。                                                               
    9) 先導式安全閥。先導式安全閥由一個主閥和一個先導閥組成。主閥是真正的安全閥,而                                                               
    先導閥的作用是感受壓力系統的壓力并使主閥開啟和關閉。主閥包括閥體和關閉件以及一個驅動機構。驅動機構可以和閥體做成一體,也可以置于閥體之外。主閥還可以由一個直接作用式安全閥附加一個驅動機構組成。先導式安全閥還可以設計成在正常運行條件下作為控制閥,而在異常運行條件下作為安全閥使用。                                                               
    此外,從安全閥的外部結構上還可以分為有扳手和無扳手安全閥、有散熱片和無散熱片安全閥、有波紋管和無波紋管安全閥等幾類。有扳手的安全閥在緊急情況下,可以由人工泄壓;有散熱片的安全閥適用于介質溫度在300℃以上的場合;有波紋管的安全閥適用于腐蝕性介質或背壓波動較大的場合。篇五:2013工作總結安監部                                                                           
    2013年度安全環保部工作總結                                                               
    安全工作                                                               
    1、辦理安全標準化三級達標企業取證工作;                                                               
    2、重大危險源上報材料;                                                               
    3、組織新上崗員工體檢、培訓28人次;                                                               
    4、代表望花區接受市應急辦檢查;                                                               
    5、按照市區安監局要求,安排公司各部門自檢自查工作。
 

網友評論 more
創想安科網站簡介會員服務廣告服務業務合作提交需求會員中心在線投稿版權聲明友情鏈接聯系我們